How do I use cloud in AutoCAD?

How do I edit a cloud in AutoCAD?

Convert an Object to a Revision Cloud

  1. Click Home tab Draw panel Revision Cloud. …
  2. At the Command prompt, specify a new minimum and maximum arc length or press Enter. …
  3. Select the circle, ellipse, polyline, or spline that you want to convert to a revision cloud. …
  4. Press Enter to change the selected object to a revision cloud.

How do you make a rectangular cloud in AutoCAD?

To create a simple revision cloud type REVCLOUD on the command line and press enter. Click at rectangular from the command line options and then click at two points in the drawing to make the rectangle. A revision cloud will be made in the drawing area as shown in the image below.

How do you reverse a revision cloud in AutoCAD?

EDIT: TLDR = REVCLOUD -> Right Click -> Left Click on inverted Revision Cloud. Repeat if Arc Length is not correct. then type “yes” to reverse. edit* might have to adjust your arch length before you modify the revcloud if its different.

IT IS INTERESTING:  How do i edit a pdf in autocad?

What is a polyline in AutoCAD?

A polyline is a connected sequence of line segments created as a single object. You can create straight line segments, arc segments, or a combination of the two. … Absolute line width (as an alternative to relative lineweight) that can be constant or tapered across a segment.

How do I adjust Rev cloud?

To Change the Default Values for Arc Lengths in a Revision Cloud

  1. Click Home tab Draw panel Revision Cloud drop-down. Find.
  2. In the drawing area, right-click and choose Arc length.
  3. Specify a new minimum arc length.
  4. Specify a new maximum arc length. …
  5. Press Enter to continue with the command or Esc to end the command.

When would you use a revision cloud?

Use revision clouds to indicate design areas that have changed in a project. You can sketch revision clouds in all views except 3D views. The cloud is visible in the view where it resides and on sheets that include the view. After entering revision information, you can assign a revision to one or more clouds.

How do you make a callout bubble in Autocad?

To Create a Callout Tool on a Tool Palette

  1. On the Tool Palettes, click (Properties), and click Document.
  2. Click the Callouts palette.
  3. Select the callout tool most similar to the tool you want to create. …
  4. Right-click, and click Copy. …
  5. Select the copied tool, right-click, and click Properties.
  6. Rename the tool as desired.

What controls the revision cloud arc length?

The Arc Length value controls the arc length for all existing and new revision cloud annotations in the project. This value sets the minimum arc length for the 2-arc segment that is used to draw the revision cloud annotation.

IT IS INTERESTING:  How do you draw furniture in autocad?

How do you make a revision cloud in Zwcad?

Create a Freehand Revision Cloud

  1. Click Home tab Draw panel Revision Cloud drop-down Freehand. Find.
  2. Guide the crosshairs along the cloud path. …
  3. Press Enter at any time to stop drawing the revision cloud. …
  4. To reverse the direction of the arcs, enter yes at the Command prompt and press Enter.

How do I make a revision cloud in MicroStation?

To draw a revision cloud in MicroStation XM, go to the Drawing Compostion task and select either Cloud by Points (S) or Cloud by Elememnt (D). Adjust the settings and follow the prompts. You can also launch these tools via Tools > Annotation > Cloud.

How do I create a revision cloud in Word?

Creating Revision Clouds

  1. Click the Revision Cloud tool from the Dims/Notes tool set.
  2. Click the Preferences button from the Tool bar to define the revision cloud properties. …
  3. Click the revision cloud mode and select to draw the cloud with either a convex or concave shape. …
  4. Click to draw the revision cloud according to the specified mode.

What are the commands of AutoCAD?

150 AutoCAD Command and Shortcut list, PDF eBook included

  • L. It can be used for making simple lines in the drawing.
  • C. It is the command used for making a circle in AutoCAD.
  • PL. This command can be used to make a Polyline in your drawing.
  • REC. This command will make a rectangle in AutoCAD.
  • POL. …
  • ARC. …
  • ELLIPSE. …
  • REG.

What is polyline tool?

The Polyline tool is used to draw shapes. It is a central vector type of line. To form a shape, you click to add a point and then, without releasing the mouse, pull the handle in the desired direction before adding the next point and repeat the operation.

IT IS INTERESTING:  Best answer: How does AutoCAD measure distance in meters?

How do I continue a polyline in AutoCAD?


  1. Click Home tab Modify panel Edit Polyline. Find.
  2. Select the polyline to modify. Note: …
  3. If the selected object is a spline, line, or an arc, the following prompt is displayed: Object selected is not a polyline. …
  4. Edit the polyline by entering one or more of the following options: …
  5. Enter x (Exit) to end a command option.
Special Project